Master Of Drive! 3 in 1 including a switch fest!

GrindCustoms · **Posted:** Thu May 03, 2012 4:18 pm

Red: Klone
Blue: OCD
Green: TS9

Flipper switch for OCD and TS9, Flipper switch for Klone and (OCD/TS9).

Overall it was pretty easy to do but.................damn it makes alot of wire! :lol:

Everything fired up instantly 45minutes ago, have something to look at in the OCD, some sort of dead spot in the volume pot...

For now it's a JRC4559 in the TS9 I'll swap it for a 4558 when they come in..... :roll:

phreek · **Posted:** Thu May 03, 2012 5:42 pm

hate...... you............ grind.... you ... bastard.............
looks awesome!! what paint is that?

those 3 circuits!! just badass! how does it sound?!?
the hilarity is, those are 2 of the 3 circuits that are giving me shit right now!!
havent troubleshot my klone yet.. set the ocd to the side.. at some point i need to get back on track with a build that works!!

in fact. screw how it sounds.. i demand clips!
many clips. not just a minute or so.. i wanna hear every damned combo it will offer! cranked to hell and back.
this will please me.

phreek · **Posted:** Thu May 03, 2012 5:43 pm

btw, is this beast a customer build, or a personal build?

GrindCustoms · **Posted:** Thu May 03, 2012 5:50 pm

Well............i have an issue with the OCD, no sound at all now, must be a grounding issue.... :roll:

Sadly it's a customer built, but the customer is my good friend, so there's no problem doing a nice clip of it.

For the moment with the klone and ts9 i extracted the most powerfull tone i ever got on my Mark4.....both pedal used as boost TS9 going into klone.......it's fakin' tight into the lead channel..... :twisted:

I tested everything on 9volt, i have to remove all the hardware and guts to do the decal job on the enclosure.

I will add the voltage regulator, so i can feed the OCD in 18v and the Klone/TS9 with 9v.

phreek · **Posted:** Thu May 03, 2012 5:55 pm

gotta ask.. how much is Rabid Uber-overkill Overdrive goin for?

GrindCustoms · **Posted:** Thu May 03, 2012 5:59 pm

phreek wrote:

gotta ask.. how much is Rabid Uber-overkill Overdrive goin for?

I asked him 350$, would have been 325..........but the knobs....... :lol:

phreek · **Posted:** Thu May 03, 2012 6:06 pm

hell of a deal!!! congrats grindy!!
again.. i hate you.

inspiring me to make one of these is just evil.
you made my brain itch.

GrindCustoms · **Posted:** Thu May 03, 2012 6:12 pm

Hahaha! Do it! :twisted:

But i'm really going to build one for me.............i may push it a bit further too.....

phreek · **Posted:** Thu May 03, 2012 6:15 pm

yeah.. seems like there should be a sho on the front end, and all run in to a fuzz to cap it off!

5 in 1. nuff said.

GrindCustoms · **Posted:** Thu May 03, 2012 6:28 pm

Yeah, that is close to what i was thinking, maybe more a clean boost at the end and a hot sillicon type fuzz at the beginning....

I like to run fuzz into the overdrive...the other way does'nt work for me... :roll:

Crankston Shnord · **Posted:** Thu May 03, 2012 10:07 pm

This one's going on my list of all time favs!! Stunning build!!

Gaetano Capuano · **Posted:** Thu May 03, 2012 10:44 pm

Yeah I like the Klon first in the chain, then TS, then OCD IMHO

GrindCustoms · **Posted:** Fri May 04, 2012 10:48 am

Crankston Shnord wrote:

This one's going on my list of all time favs!! Stunning build!!

Thanks alot buddy, i'm also really happy of it, my most «complex» built to date! :mrgreen:

Gaetano Capuano wrote:

Yeah I like the Klon first in the chain, then TS, then OCD IMHO

When the Klone is used as an OD it really makes a great job when in front, but in clean boost usage his place really belongs at the end of the chain imo.

The addition of tight «Ooommph» and midrange crunch that it gives his absolutely perfect!

TNblueshawk · **Posted:** Fri May 04, 2012 1:38 pm

Dang, you are back and better than ever. Did you use the layout on the flipper switch that you posted, that I printed and have in my wiring folder? You remember that thread about a month ago. Forget the subject title now. Or, did you do something different from that?

Awesome pedal. That's a 1590DD size enclosure?

tonedeaf · **Posted:** Fri May 04, 2012 2:06 pm

Oh snap! That's a lot of overdrive all in one place. The paint is killer. Like marbelized pearl, but cracked. Killer!

GrindCustoms · **Posted:** Fri May 04, 2012 2:16 pm

TNblueshawk wrote:

Dang, you are back and better than ever. Did you use the layout on the flipper switch that you posted, that I printed and have in my wiring folder? You remember that thread about a month ago. Forget the subject title now. Or, did you do something different from that?

Awesome pedal. That's a 1590DD size enclosure?

Thanks man, yup it's the flipper switch layout that i posted in couple occasion, only «mod» is that it's doubled.

1590DD enclosure....could'nt use anything smaller than that.....

tonedeaf wrote:

Oh snap! That's a lot of overdrive all in one place. The paint is killer. Like marbelized pearl, but cracked. Killer!

I got the enclosure painted seafoam green from Used666 in the first part lot i ever bought on the forum!

And i just used the silver hammered spray can that i've been using for couple builts.

Only one super thick coat, don't let dry, all wet in the Toast-R-Over at 350F for 45minutes and that what you get! :lol:

tonedeaf · **Posted:** Fri May 04, 2012 2:22 pm

Rej - love it. No time honored and well researched painting techniques, just a whole lot of 'eff it let's see what THIS does' and it comes out beautiful.

hogharry · **Posted:** Fri May 04, 2012 3:01 pm

Awesome Rej! Now I know why you wanted the double flipper. Do I get a consults fee for helping with the doubling part ? Did I say awesome? Yes indeed!

hogharry · **Posted:** Fri May 04, 2012 4:03 pm

GrindCustoms wrote:

i have to remove all the hardware and guts to do the decal job

Finally a build where you have to label the knobs! ...you are going to label them aren't you? Or is it going to be a memory test? :lol:

GrindCustoms · **Posted:** Fri May 04, 2012 4:38 pm

hogharry wrote:

GrindCustoms wrote:

i have to remove all the hardware and guts to do the decal job

Finally a build where you have to label the knobs! ...you are going to label them aren't you? Or is it going to be a memory test? :lol:

They will all be labeled, this enclosure his part of the lot that i'm bringing over monday for some Laser Etching Action!

DrRJE · **Posted:** Fri May 04, 2012 10:58 pm

can't wait to see it finished.

tonedeaf · **Posted:** Sat May 05, 2012 5:54 am

All I want is some frickin sharks with some frickin laser beams. Is that too much to ask?

GrindCustoms · **Posted:** Sat May 05, 2012 8:50 am

tonedeaf wrote:

All I want is some frickin sharks with some frickin laser beams. Is that too much to ask?

Hahahaha, we listened to the 3 AustinPowers while a work, 3 evening in a row!

Kunfuz · **Posted:** Thu May 10, 2012 11:42 pm

Lunar base is complete Rej :lol:

Build Your Own Clone Message Board

Master Of Drive! 3 in 1 including a switch fest!

Who is online